 |
 |
Test scope |
Test connection
|
Test condition |
Nominal value |
Possible cause/Remedy |
| 1.0 |
|
Voltage supply
Circuit 30 |
12 
|
N52
Z 
 |
 11
|
|
11 - 14 V |
Wiring. |
| 2.0 |
|
Voltage supply
Circuit 15, 31
|
10 |
N52
X 
|
12
|
Ignition: ON |
11 - 14 V |
Wiring. |
| 3.0 |
|
Hydraulic unit (A7/5)
Hydraulic unit motor (A7/5m1) control signal
|
10 |
N52
X
|
7
|
Ignition: ON
Operate power soft switch towards open or close. |
0 - 1 V
11 - 14 V
Hydraulic unit runs. |
23 23.0
Power soft top control module (N52)
23
23.0
Power soft top switch (S84)
(N52)
3.2
Hydraulic unit motor (A7/5m1)
3.3
Hydraulic unit relay (A7/5k1)
3.1
|
| 3.1 |
|
Hydraulic unit
relay (A7/5k1)
Activation |
5 |
A7/5x1
|
6
|
Ignition: OFF
Unplug connector A7/5x1
Ignition: ON
Move power soft top switch (S84) toward Open or Close. |
0 - 1 V
11 - 14 V
|
Wiring,
Power soft top switch (S84),
Power soft top control
module (N52).
Wiring. |
| 3.2 |
|
Hydraulic unit
motor (A7/5m1)
Voltage supply
|
1 |
A7/5x1
|
4
|
Unplug connector A7/5x1. |
11 - 14 V |
Wiring. |
| 3.3 |
|
Hydraulic unit
motor (A7/5m1) |
1  |
A7/5x1
 |
 4
|
Unplug connector A7/5x1,
Remove relay A7/5k1, Bridge sockets 1 and 3 of relay connector A7/5k1
|
0.1 - 1.5  |
A7/5m1,
See SMS, Job No. 77-350
|
| 4.0 |
 |
Left cover "Locked"
switch (A24s2)
|
 |
|
N52
Y
20 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top compartment
cover:
locked:
unlocked: |
0 - 1 V
11 - 14 V
|
Wiring,
(A24s2),
4.1,
See SMS, Job no. 77-440,
Wiring,
(A24s2),
4.1,
N52 |
| 4.1 |
|
Left cover "Locked"
switch (A24s2)
|
|
|
N52
Y
20 |
Ignition: OFF
Disconnect test cable from N52,
Soft top compartment
cover:
locked:
unlocked: |
0 - 5
>20 k
|
Wiring,
(A24s2)
Wiring,
(A24s2)
|
| 5.0 |
 |
Right cover "Locked"
switch (A25s2) |
|
|
N52
Y
21 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top compartment
cover:
locked:
unlocked: |
0 - 1 V
11 - 14 V
|
Wiring,
(A25s2),
5.1,
See SMS, Job no. 77-440,
Wiring,
(A25s2),
5.1,
N52
|
| 5.1 |
|
Right cover "Locked" switch
(A25s2) |
|
|
N52
Y
21 |
Ignition: OFF
Disconnect test cable from
N52
Soft top compartment
cover:
locked:
unlocked: |
0 - 5
>20 k
|
Wiring,
(A25s2)
Wiring,
(A25s2)
|
| 6.0 |
 |
Left cover "Closed"
switch (A24s1) |
|
|
N52
Y
25 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top compartment
cover:
closed:
raised: |
0 - 1 V
11 - 14 V
|
Wiring,
(A24s1),
6.1,
See SMS, Job no. 77-440
Wiring,
(A24s1),
6.1,
N52
|
| 6.1 |
|
Left cover "Closed"
switch (A24s1) |
|
|
N52
Y
25 |
Ignition: OFF
Disconnect test cable from N52
Soft top compartment
cover:
closed:
raised: |
0 - 5
>20 k
|
Wiring,
(A24s1)
Wiring,
(A24s1)
|
| 7.0 |
 |
Right cover"Closed"
switch (A25s1) |
|
|
N52
Y
26 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top compartment
cover:
closed:
raised: |
0 - 1 V
11 - 14 V
|
Wiring,
(A25s1),
7.1
See SMS, Job No. 77-440
Wiring,
(A25s1),
7.1,
N52
|
| 7.1 |
|
Right cover"Closed"
switch (A25s1) |
|
|
N52
Y
26 |
Ignition: OFF
Disconnect test cable from N52
Soft top compartment
cover:
closed:
raised: |
0 - 5
>20 k
|
Wiring,
(A25s1)
Wiring,
(A25s1)
|
| 8.0 |
 |
Left bow "Locked"
switch (A22s2) |
|
N52
Y
|
18
|
Power soft top control
module in diagnostic
mode, see 22.
Fabric bow:
locked:
unlocked: |
0 - 1 V
11 - 14 V
|
Wiring,
(A22s2),
8.1
See SMS, Job no. 77-445
Wiring,
(A22s2),
8.1,
N52
|
| 8.1 |
|
Left bow "Locked"
switch (A22s2) |
|
N52
Y
|
18
|
Ignition: OFF
Disconnect test cable from N52
Fabric bow:
locked:
unlocked: |
0 - 5
>20 k
|
Wiring,
(A22s2)
Wiring,
(A22s2)
|
| 9.0 |
 |
Right bow "Locked"
switch (A23s2) |
|
|
N52
Y
19 |
Power soft top control
module in diagnostic
mode, see 22.
Fabric bow:
locked:
unlocked: |
0 - 1 V
11 - 14 V
|
Wiring,
(A23s2),
9.1
See SMS, Job no. 77-445
Wiring,
(A23s2)
9.1,
N52
|
| 9.1 |
|
Right bow "Locked"
switch (A23s2) |
|
|
N52
Y
19 |
Ignition: OFF
Disconnect test cable from N52
fabric bow:
locked:
unlocked: |
0 - 5
>20 k |
Wiring,
(A23s2)
Wiring,
(A23s2)
|
| 10.0 |
 |
Left bow "Closed"
switch (A22s1) |
|
|
N52
Y
23 |
Power soft top control
module in diagnostic
mode, see 22.
Fabric bow:
closed:
raised: |
0 - 1 V
11 - 14 V
|
Wiring,
(A22s1),
10.1
See SMS, Job no. 77-445
Wiring,
(A22s1)
10.1,
N52
|
| 10.1 |
|
Left bow "Closed"
switch (A22s1) |
|
|
N52
Y
23 |
Ignition: OFF
Disconnect test cable from
N52
Fabric bow:
closed:
raised: |
0 - 5
>20 k
|
Wiring,
(A22s1)
Wiring,
(A22s1),
A/c pushbutton control
module (N22).
|
| 11.0 |
 |
Right bow "Closed"
switch (A23s1) |
|
|
N52
Y
24 |
Power soft top control
module in diagnostic
mode, see 22.
Fabric bow:
closed:
raised: |
0 - 1 V
11 - 14 V |
Wiring,
(A23s1),
11.1
See SMS, Job no. 77-445
Wiring,
(A23s1),
11.1
N52
|
| 11.1 |
|
Right bow "Closed"
switch (A23s1) |
|
|
N52
Y
24 |
Ignition: OFF
Disconnect test cable from N52
Fabric bow:
closed:
raised: |
0 - 5
>20 k
|
Wiring,
(A23s1)
Wiring,
(A23s1)
|
| 12.0 |
  |
Left front soft top "Locked"
switch (S84/1) |
|
|
N52
Y
16 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top:
Locked in front:
Unlocked in front: |
0 - 1 V
11 - 14 V
|
Wiring,
(S84/1),
12.1
See SMS, Job no. 77-330
Wiring,
(S84/1),
12.1
N52
|
| 12.1 |
|
Left front soft top "Locked"
switch (S84/1) |
|
|
N52
Y
16 |
Ignition: OFF
Disconnect test cable from N52
Soft top:
Locked in front:
Unlocked in front: |
0 - 5
>20 k
|
Wiring,
S84/3 (SMS, Job no. 77-425).
Wiring,
(S84/1)
Wiring,
(S84/1)
|
| 13.0 |
|
Right front soft top "Locked"
switch (S84/2) |
|
|
N52
Y
17 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top:
Locked in front:
Unlocked in front: |
0 - 1 V
11 - 14 V
|
Wiring,
(S84/2),
13.1
See SMS, Job no. 77-330
Wiring,
(S84/2),
13.1
N52
|
| 13.1 |
|
Right front soft top "Locked"
switch (S84/2) |
|
|
N52
Y
17 |
Ignition: OFF
Disconnect test cable from N52
Soft top:
Locked in front:
Unlocked in front: |
0 - 5
>20 k
|
Wiring,
(S84/2)
Wiring,
(S84/2)
|
| 14.0 |
|
Soft top compartment "Open"
switch (S84/5) |
|
|
N52
Y
30 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top compartment cover:
open:
closed: |
0 - 1 V
11 - 14 V
|
Wiring,
(S84/5),
14.1
See SMS, Job no. 77-405
Wiring,
(S84/5),
14.1
N52
|
| 14.1 |
|
Soft top compartment "Open"
switch (S84/5) |
|
|
N52
Y
30 |
Ignition: OFF
Disconnect test cable from N52
Soft top compartment cover:
open:
closed: |
0 - 5
>20 k
|
Wiring,
(S84/5)
Wiring,
(S84/5)
|
| 15.0 |
|
Soft top fabric bow "Raised"
switch (S84/6)
(fabric bow raised) |
|
|
N52
Y
29 |
Power soft top control
module in diagnostic
mode, see 22.
Fabric bow:
raised:
lowered: |
0 - 1 V
11 - 14 V
|
Wiring,
(S84/6),
15.1
See SMS, Job no. 77-435
Wiring,
(S84/6),
15.1
N52
|
| 15.1 |
|
Soft top fabric bow "Raised"
switch (S84/6)
(fabric bow raised) |
|
|
N52
Y
29 |
Ignition: OFF
Disconnect test cable from N52.
Fabric bow:
raised:
lowered: |
0 - 5
>20 k
|
Wiring,
(S84/6)
Wiring,
(S84/6)
|
| 16.0 |
|
Soft top "Open"
switch (S84/3)
(soft top in storage compartment) |
|
|
N52
Y
27 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top:
in soft top compartment:
up: |
0 - 1 V
11 - 14 V
|
Wiring,
(S84/3),
16.1
See SMS, Job no. 77-425
Wiring,
(S84/3),
16.1
N52
|
| 16.1 |
|
Soft top "Open"
switch (S84/3)
(soft top in storage compartment) |
|
|
N52
Y
27 |
Ignition: OFF
Disconnect test cable from N52.
Soft top:
in soft top compartment:
up: |
0 - 5
>20 k
|
Wiring,
(S84/3)
Wiring,
(S84/3)
|
| 17.0 |
|
Soft top "Raised"
switch (S84/4) |
|
|
N52
Y
28 |
Power soft top control
module in diagnostic
mode, see 22.
Soft top:
up:
in soft top compartment:
|
0 - 1 V
11 - 14 V |
Wiring,
(S84/4),
17.1
See SMS, Job no. 77-415
Wiring,
(S84/3),
17.1
N52
|
| 17.1 |
|
Soft top "Raised"
switch (S84/4) |
|
|
N52
Y
28 |
Ignition: OFF
Disconnect test cable from N52.
Soft top:
up:
in soft top compartment:
|
0 - 5
>20 k
|
Wiring,
(S84/4)
Wiring,
(S84/4)
|
| 18.0 |
|
RB "Retracted"
switch (S83/1) |
|
|
N52
Y
31 |
Power soft top control
module in diagnostic
mode, see 22.
Roll bar:
lowered:
raised:
|
0 - 1 V
11 - 14 V |
Wiring,
(S83/1),
18.1
See SMS, Job no. 77-400
Wiring,
(S83/1),
18.1
N52
|
| 18.1 |
|
RB "Retracted"
switch (S83/1) |
|
|
N52
Y
31 |
Ignition: OFF
Disconnect test cable from N52.
Roll bar:
lowered:
raised: |
0 - 5
>20 k |
Wiring,
(S83/1)
Wiring,
(S83/1)
|
| 19.0 |
|
Left front door "window down"
limit switch (S21/9) |
|
|
N52
Y
10 |
Power soft top control
module in diagnostic
mode, see 22.
Side windows:
down:
up:
|
0 - 1 V
11 - 14 V |
Wiring,
(S21/9),
19.1
See SMS, Job no. 77-410
Wiring,
(S21/9),
19.1
N52
|
| 19.1 |
|
Left front door "window down"
limit switch (S21/9) |
|
|
N52
Y
3 |
Ignition: OFF
Disconnect test cable from N52.
Side windows:
down:
up: |
0 - 5
>20 k
|
Wiring,
(S21/9)
Wiring,
(S21/9)
|
| 20.0 |
|
Right front door "window
down" limit switch (S21/8)
|
|
|
N52
Y
22 |
Power soft top control
module in diagnostic
mode, see 22.
Side windows:
down:
up:
|
0 - 1 V
11 - 14 V
|
Wiring,
(S21/8),
20.1
See SMS, Job no. 77-410
Wiring,
(S21/8),
20.1
N52
|
| 20.1 |
|
Right front power window motor (M10/4)
Voltage supply
control module
|
|
|
N52
Y
22 |
Ignition: OFF
Disconnect test cable from N52
Side windows:
down:
up:
|
0 - 5
>20 k |
Wiring,
(S21/8)
Wiring,
(S21/8) |
| 21.0 |
|
VSS
illogical signal
See 12/3, regarding hints when using
dynamometer or brake test equipment.
|
-
|
-
|
-
|
-
|
- |
With vehicle stationary, an acceleration
of .49 g error signal was sent to the control module, or vehicle was tilted
to a 23° angle.
RB control module (N53). |
| 22.0 |
|
Installed hardtop recognized |
|
|
|
See Hard top Locking Table in
24,
(Limit switches) |
Hard top installed.
|
With the hard top installed, at least
one of the front or rear locks indicates "closed" or "locked".
|
| 23.0 |
|
Power soft top
switch (S84) |
|
|
|
Ignition: ON
Power soft top
switch (S84):
Press close:
Ignition: ON
Power soft top
switch (S84):
Press open:
|
11 - 14 V
0 - 1 V
11 - 14 V
0 - 1 V |
Switch (S84) and wiring,
23.1,
N52
Switch (S84) and wiring,
23.1,
N52
Switch (S84) and wiring,
23.1,
N52
Switch (S84) and wiring,
23.1,
N52
|
| 23.1 |
|
Power soft top
switch (S84) and wiring
|
|
|
|
Disconnect test cable from N52
Power soft top
switch (S84):
In rest position:
Press in direction close:
Power soft top
switch (S84):
In rest position:
Press in direction open: |
>20 k
0 - 5
>20 k
0 - 5 |
Wiring,
(S84)
Wiring,
(S84)
Wiring,
(S84)
Wiring,
(S84)
|
| 24.0 |
|
RB switch (S83)
(manual operation)
|
|
|
|
Ignition: ON
Roll bar
switch (S83):
Press in direction Up
Ignition: ON
Roll bar
switch (S83):
Press in direction Lower |
4 - 6 V
0 - 1 V
4 - 6 V
0 - 1 V |
Switch (S83) and wiring,
24.1,
N52
Switch (S83) and wiring,
24.1,
N52
Switch (S83) and wiring,
24.1,
N52
Switch (S83) and wiring,
24.1,
N52
|
| 24.1 |
|
RB switch (S83) and wiring
|
|
|
|
Disconnect test cable from N52
Roll bar
switch (S83):
In rest position:
Press in direction Raise
Roll bar
switch (S83):
In rest position:
Press in direction Lower: |
>20 k
0 - 5
>20 k
0 - 5 |
Wiring,
(S83)
Wiring,
(S83)
Wiring,
(S83)
Wiring,
(S83)
|
| 25.0 |
|
RB control module (N53)
|
|
|
|
Ignition: ON
|
>2.4 V
>2.4 V
|
Wiring,
Fault in the Roll bar system, see
DM, B&A, Vol. 6, section 19.2,
N53,
See SMS, Job no. 91-840
Wiring,
Fault in the Roll bar system, see
DM, B&A, Vol. 6, section 19.2,
N53
|
| 26.0 |
|
Roll Bar
(Crash Deployment) |
|
|
N52
Y
9
|
Ignition: ON
RB switch (S83):
Press in direction "up"
(approx. 10 seconds)
Using RB switch (S83): Lower roll bar
|
Roll bar is lowered.
|
There has been a "Crash Deployment".
Upon lowering the roll bar, the impulse (DTC) is erased.
|
| 27.0 |
|
Limit switch un-logical |
-
|
-
|
-
|
Test limit switch via diagnostic
mode,
see 22
|
- |
Limit switch is faulty. |
| 28.0 |
|
Operation time span exceeded |
-
|
-
|
-
|
Soft top completely open or closed.
Ignition: ON
(approx. 5 minutes)
|
Fault will erase itself. |
N52 |
| 29.0 |
|
Low system voltage |
10 |
N52
X
|
12
|
Ignition: ON
Use battery charger each time when performing soft top tests.
|
11 - 14 V |
Voltage supply,
23
2.0 |
| 30.0 |
|
Speedometer signal
See 12/3, regarding hints when using
dynamometer or brake test equipment.
|
|
|
N52
Y
35 |
Drive vehicle at approx. 25 mph. |
approx. 6 V ~ |
Wiring,
Electronic speedometer (A1p8)
(see DM, Info. & Com., section 1.1),
Combination relay
module (N10/2),
Pushbutton control
module (N22),
Radio (A2),
Multi-function connector
block (X30/1).
|
| 31.0 |
|
VSS signal
See 12/3, regarding hints when using
dynamometer or brake test equipment.
|
|
|
N52
Y
9 |
Ignition: ON
Rotate left front wheel at approx. 1 revo./second |
2.5 - 4 V |
Wiring,
ABS control module (N30),
Power soft top control
module (N52).
|
| 32.0 |
|
Power soft top operation locked
See 12/3, regarding hints when using
dynamometer or brake test equipment.
|
- |
-
|
-
|
- |
- |
Fault only occurs with impluse readouts
(DTCs'): 19, 28 or 29 |
| 33.0 |
|
Left front power window switch
(S21/1) |
|
|
|
Ignition: ON |
11 - 14 V
11 - 14 V |
Wiring,
Power soft top control
module (N52),
(S21/1),
33.1
Wiring,
Power soft top control
module (N52),
(S21/1),
33.2
|
| 33.1 |
|
Left front power window switch (S21/1)
Close,
lower limit stop control |
|
|
N52
Y
5 |
Ignition: OFF
Disconnect test cable from N52,
Press switch (S21/1) back to second detent and then forward. |
>20 k
0 - 1
|
Wiring,
(S21/1),
Wiring,
(S21/1)
|
| 33.2 |
|
Left front power window switch
(S21/1)
Open |
|
|
N52
Y
6 |
Ignition: OFF
Disconnect test cable from N52,
Press switch (S21/1) back to first and second detent. |
>20 k
0 - 1 |
Wiring,
(S21/1)
Wiring,
(S21/1)
|
| 34.0 |
|
Right front power window switch
(S21/2) |
|
|
|
Ignition: ON |
11 - 14 V
11 - 14 V |
Wiring,
(S21/2),
34.1,
Power soft top control
module (N52).
Wiring,
(S21/2),
34.2,
Power soft top control
module (N52).
|
| 34.1 |
|
Right front power window switch (S21/2)
Close,
lower limit stop control |
|
|
N52
Y
7 |
Ignition: OFF
Disconnect test cable from N52,
Press switch (S21/1) back to second detent and then forward. |
>20 k
0 - 1
|
Wiring,
(S21/2)
Wiring,
(S21/2)
|
| 34.2 |
|
Right front power window switch (S21/2)
Open |
|
|
N52
Y
8 |
Ignition: OFF
Disconnect test cable from N52,
Press switch (S21/1) back to first and second detent. |
>20 k
0 - 1 |
Wiring,
(S21/2)
Wiring,
(S21/2)
|
| 35.0 |
|
Left front power window motor
(M10/3)
Voltage |
2
1 |
|
1
2
|
Ignition: ON
Switch (S21/1):
At rest:
Press in direction "open"
Press in direction "close"
|
0 - 1 V
11 - 14 V
11 - 14 V
|
Power soft top control
module (N52)
Wiring,
(M10/3),
35.1,
(N52).
Wiring,
(M10/3),
35.1,
(N52).
|
| 35.1 |
|
Left front power window motor (M10/3)
(with wiring) |
1
9 |
|
2
2
|
Ignition: OFF
Disconnect test cable from N52. |
0.5 - 2
>20 k |
Wiring,
(M10/3),
See SMS, Job no. 82-600
Wiring,
(M10/3)
|
| 36.0 |
|
Right front power window motor
(M10/4)
Voltage |
2
1 |
|
1
2
|
Ignition: ON
Switch (S21/1):
At rest:
Press in direction "open"
Press in direction "close"
|
0 - 1 V
11 - 14 V
11 - 14 V
|
Power soft top control
module (N52).
Wiring,
(M10/4),
36.1,
(N52).
Wiring,
(M10/4),
36.1,
(N52).
|
| 36.1 |
|
Right front power window motor (M10/4)
(with wiring) |
1
12 |
|
2
2
|
Ignition: OFF
Disconnect test cable from N52. |
0.5 - 2
>20 k |
Wiring,
(M10/4),
See SMS, Job no. 82-600
Wiring,
(M10/4).
|
| 37.0 |
|
Indicator lamp in power soft top
switch (S84) |
|
|
|
Ignition: ON |
Indicator lamp in power soft top switch
illuminates briefly.
|
Wiring,
(S84). |
| 38.0 |
|
Main valve (A7/5y1)
Activation
(deleted as of VIN 1F-083891)
|
10
|
N52
X
|
8
|
Ignition: ON
Roll bar retracted.
Press power soft top switch (S84) to "open" or "close".
|
0 - 1 V
11 - 14 V |
Power soft top control
module (N52).
23
39.0,
(N52)
|
| 39.0 |
|
Main valve (A7/5y1)
with wires
|
10
|
N52
X
|
8
|
Disconnect test cable from N52.
See connection
schematic X
|
5 - 15 |
Wiring,
(A7/5y1) |
| 40.0 |
|
Rear locks valve (Y56y2)
Activation
|
12
|
N52
Z
|
4
|
Ignition: ON
Unlock hard top, or
unlock fabric bow using power soft top switch (S84).
Lock hard top, or
unlock fabric bow using power soft top switch (S84).
|
11 - 14 V
0 - 1 V
|
23 41.0,
(N52).
(N52).
|
| 41.0 |
|
Rear locks valve (Y56y2)
with wiring
|
12
|
N52
Z
|
4
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y56y2),
If nominal value is OK:
Check if rear locks valve (Y56y2) is mechanically jammed.
|
| 42.0 |
|
Center locks valve (Y56y3)
Activation
|
12
|
N52
Z
|
5
|
Ignition: ON
Using power soft top switch (S84):
"Open " soft top compartment cover.
"Close" soft top compartment cover.
|
11 - 14 V
0 - 1 V
|
23 43.0,
(N52).
(N52).
|
| 43.0 |
|
Center locks valve (Y56y3)
with wiring
|
12
|
N52
Z
|
5
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y56y3),
If nominal value is OK:
Check if center locks valve (Y56y3) is mechanically jammed.
|
| 44.0 |
|
Front locks valve (Y56y4)
Activation
|
12
|
N52
Z
|
3
|
Ignition: ON
Unlock hard top, or
unlock front soft top using power soft top switch (S84).
Lock hard top, or
unlock front soft top using power soft top switch (S84).
|
11 - 14 V
0 - 1 V
|
23 45.0,
(N52).
(N52).
|
| 45.0 |
|
Front locks valve (Y56y4)
with wiring
|
12
|
N52
Z
|
3
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y56y4),
If nominal value is OK:
Check if front locks valve (Y56y4) is mechanically jammed.
|
| 46.0 |
|
Soft top compartment cover valve
(Y56y5)
Activation
|
12
|
N52
Z
|
6
|
Ignition: ON
Using power soft top switch (S84):
"Open " soft top compartment cover.
"Close" soft top compartment cover.
|
11 - 14 V
0 - 1 V
|
23 47.0,
(N52).
(N52).
|
| 47.0 |
|
Soft top compartment cover valve
(Y56y5)
with wiring
|
12
|
N52
Z
|
6
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y56y5),
If nominal value is OK:
Check if soft top compartment cover valve (Y56y5) is mechanically jammed.
|
| 48.0 |
|
Soft top "open"
valve (Y55y6)
Activation
|
10
|
N52
Z
|
3
|
Ignition: ON
Using power soft top switch (S84):
"Open " soft top.
"Close" soft top.
|
11 - 14 V
0 - 1 V
|
23 49.0,
(N52).
(N52).
|
| 49.0 |
|
Soft top "open"
valve (Y55y6)
with wiring
|
10
|
N52
X
|
3
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y55y6),
If nominal value is OK:
Check if soft top "open" valve (Y55y6) is mechanically jammed.
|
| 50.0 |
|
Soft top "close"
valve (Y55y7)
Activation
|
10
|
N52
X
|
4
|
Ignition: ON
Using power soft top switch (S84):
"Close " soft top.
"Open" soft top.
|
11 - 14 V
0 - 1 V
|
23 51.0,
(N52).
(N52).
|
| 51.0 |
|
Soft top "close"
valve (Y55y7)
with wiring
|
10
|
N52
X
|
4
|
Disconnect test cable from N52.
|
5 - 15 |
Wiring,
(Y55y7),
If nominal value is OK:
Check if soft top "close" valve (Y55y7) is mechanically jammed.
|
| 52.0 |
|
Fabric bow "raise"
valve (Y55y8)
Activation
|
10
|
N52
X
|
5
|
Ignition: ON
Using power soft top switch (S84):
"Raise " fabric bow or
"Close" soft top.
Using power soft top switch (S84):
"Lower" fabric bow or
"Close" power soft top compartment cover. |
11 - 14 V
0 - 1 V
|
23 53.0,
(N52).
(N52). |
| 53.0 |
|
Fabric bow "raise"
valve (Y55y8)
with wiring |
10 |
N52
X
|
5
|
Disconnect test cable from N52. |
5 - 15 |
Wiring,
(Y55y8),
If nominal value is OK:
Check if fabric bow "raise" valve (Y55y8) is mechanically jammed.
|
| 54.0 |
|
Fabric bow "lower"
valve (Y55y9)
Activation
|
10
|
N52
X
|
6
|
Ignition: ON
Using power soft top switch (S84):
"Lower " fabric bow.
Using power soft top switch (S84):
"Raise" fabric bow. |
11 - 14 V
0 - 1 V
|
23 55.0,
(N52).
(N52). |
| 55.0 |
|
Fabric bow "lower"
valve (Y55y9)
with wiring |
10 |
N52
X
|
6
|
Disconnect test cable from N52. |
5 - 15 |
Wiring,
(Y55y9),
If nominal value is OK:
Check if fabric bow "lower" valve (Y55y9) is mechanically jammed.
|
| 56.0 |
|
Rod side
valve (Y57y10)
Activation
|
10
|
N52
X
|
7
|
Ignition: ON
Press power soft top switch (S84),
Or
RB switch (S83). |
0 - 1 V
11 - 14 V
|
Power soft top control
module (N52).
23
57.0,
Wiring,
(N52).
|
| 57.0 |
|
Rod side
valve (Y57y10)
with wiring
|
10
|
N52
X
|
7
|
Disconnect test cable from N52. |
5 - 15
|
Wiring,
(Y57y10).
|
| 58.0 |
|
Piston side
valve (Y57y11)
Activation
|
12
|
N52
Z
|
8
|
Ignition: ON
Press power soft top switch (S84) or
RB switch (S83):
To "raise" roll bar
or
to "lower" roll bar. |
11 - 14 V
0 - 1 V |
23 59.0,
(N52).
(N52).
|
| 59.0 |
|
Piston side
valve (Y57y11)
with wiring
|
12
|
N52
Z
|
8
|
Disconnect test cable from N52. |
5 - 15
|
Wiring,
(Y57y11)
If nominal value is OK:
Check if piston side valve (Y55y11) is mechanically jammed.
|
| 60.0 |
|
ATA/CF microswitch
Driver's door (S86),
Passenger side door (S87s1),
Trunk lid (S88s1)
|
|
|
N52
Y
14 |
Ignition: OFF
Microswitches (S86), S87s1) and S88s1) in:
Rest position:
Microswitch (S86) in position:
Close:
Microswitch (S87s1) in position:
Close:
Microswitch (S88s1) in position:
Close:
|
11 - 14 V
0 - 1 V
0 - 1 V
0 - 1 V |
(S86),
60.1,
(S87s1),
60.1,
(S88s1),
60.1,
Supply pump
(CL/vacuum) (M14/1),
CF control module (N57),
ATA control module (N26),
RCL control module (N57).
Wiring,
(S86)
Wiring,
(S87s1)
Wiring,
(S88s1)
|
| 60.1 |
|
ATA/CF microswitch
Driver's door (S86),
Passenger side door (S87s1),
Trunk lid (S88s1)
|
|
|
N52
Y
14 |
Ignition: OFF
Disconnect control modules from socket box, disconnect connectors from:
Supply pump
(CL/vacuum) (M14/1),
CF control module (N57),
ATA control
module (N26),
RCL control module (N57)
Microswitches (S86), (S87s1) and (S88s1) in:
Rest position:
Microswitch (S86) in position:
Close:
Microswitch (S87s1) in position:
Close:
Microswitch (S88s1) in position:
Close:
|
>20 k
<10
<10
<10 |
Wiring,
(S86),
(S87s1),
(S88s1).
Wiring,
(S86).
Wiring,
(S87s1).
Wiring,
(S88s1).
|
| 61.0 |
|
Actuator:
Left door actuator (S47),
Right door actuator (S48),
Trunk lid lock actuator (S49)
|
|
|
N52
Y
13 |
Vehicle locked via RCL |
<10 |
Wiring,
Actuators:
(S47),
(S48),
(S49).
|
Printable
version
CAUTION!
