 |
 |
Test scope |
Test connection
|
Test condition |
Nominal value |
Possible cause/Remedy |
| 1.0 |
   |
CC switch (S40)
Model 124, 202, 210
V Decelerate/set
SP Resume
B Accelerate/set
A Off
Control switch contact |
38 
(1.38)
38
(1.38)
38
(1.38)
38
(1.38)
38
(1.38) |
|
 10
(1.10)
31
(1.31)
11
(1.11)
33
(1.33)
2
(1.2) |
Ignition: ON
CC switch not activated
Position DECEL
Position RESUME
Position ACCEL
Switch not activated
Position OFF
Switch not activated
Control switch contact in position:
DECEL., ACCEL., RESUME OFF
|
< 1 V
11 - 14 V
11 - 14 V
11 - 14 V
11 - 14 V
< 1 V
< 1 V
11 - 14 V |
Wiring,
Cruise control switch (S40). |
| [1.0] |
|
Models 129, 140
V Decelerate/set
SP Resume
B Accelerate/set
A Off
Control switch contact |
79
(1.38)
79
(1.38)
79
(1.38)
79
(1.38)
79
(1.38) |
|
51
(1.10)
72
(1.31)
52
(1.11)
74
(1.33)
43
(1.2) |
Ignition: ON
CC switch not activated
Position DECEL
Position RESUME
Position ACCEL
Switch not activated
Position OFF
Switch not activated
Control switch contact in position:
DECEL., ACCEL., RESUME, OFF
|
< 1 V
11 - 14 V
11 - 14 V
11 - 14 V
11 - 14 V
< 1 V
< 1 V
11 - 14 V |
|
| 2.0 |
 |
Stop lamp switch (S9/1)
Signal (N.O. contact)
Model 124, 202, 210
Model 129, 140
Signal (N.C. contact)
Model 124, 202, 210
Model 129, 140 |
38
(1.38)
79
(1.38)
38
(1.38)
79
(1.38)
|
|
30
(1.30)
71
(1.30)
13
(1.13)
54
(1.13) |
Ignition: ON
Brake pedal not applied
Brake pedal applied
Ignition: ON
Brake pedal not applied
Brake pedal applied |
<1 V
11 - 14 V
11 - 14 V
<1 V |
Wiring,
Stop lamp switch (S9/1). |
| 3.0 |
 |
Starter lock-out/backup lamp switch (S16/1)
Selector lever position recognition
Model 124, 202, 210
Model 129, 140 |
4
(1.4)
38
(1.38)
4
(1.4)
38
(1.38)
|
|
35
(1.35)
29
(1.29)
35
(1.35)
29
(1.29) |
Ignition: ON
Transmission range: P/N
R/D/3/2
Ignition: ON
Transmission range: R
P/N/D/3/2
Ignition: ON
Transmission range: P/N
R/D/3/2
Ignition: ON
Transmission range: R
P/N/D/3/2 |
11 - 14 V
< 1 V
11 - 14 V
< 1 V
11 - 14 V
< 1 V
11 - 14 V
< 1 V
|
Wiring,
Starter lock-out/backup lamp
switch (S16/1). |
| 4.0 |
 
 |
Left front axle VSS
sensor (L6/1)
Speed signal
Model 124, 202, 210
Model 129, 140 |
38
(1.38)
79
(1.38)
|
|
15
(1.15)
56
(1.15) |
Lift front of vehicle:
Ignition: ON
Turn left front wheel by hand.
Note:
Upon completion of test, erase DTC's from ASR control module memory |
> 3 V~
> 3 V~ |
Wiring,
Left front axle VSS sensor (L6/1),
DM, Chassis & Drivetrain, Vol. 2, section 5. |
| 5.0 |
 |
CAN data bus
Model 124, 202, 210
Model 129, 140 |
20
(1.20)
"L"
|
|
21
(1.21)
"H"
|
Ignition: OFF
Ignition: OFF
Remove contact module.
Measure resistance at connector for control module N4/1.
|
55 - 65 
115 - 125 |
Wiring,
Engine control module (N3/4),
EA/CC/ISC control module (N4/1). |
Printable version
