 |
 |
Test scope |
Test connection
|
Test condition |
Nominal value |
Possible cause/ remedy |
| 1.0 |
    
|
PSE control module (A37)
Voltage supply
Circuit 30
|
3 
(2)
|
A37
|
 4
(2)
|
- |
11 - 14 V
|
Wiring. |
| |
|
Circuit 30 |
3
(2)
|
|
2
(2) |
- |
11 - 14 V |
Wiring. |
| 2.0 |
|
Left front door
switch (S17/3)
Alarm circuit |
A37
60
(1.14) |
|
A37
4
(2)
|
Left front door:
closed
open |
< 1 V
11 - 14 V |
Wiring,
S17/3 |
| 3.0 |
 |
Right front door
switch (S17/4)
Alarm circuit |
A37
62
(1.16)
|
|
A37
4
(2)
|
Right front door:
closed
open |
< 1 V
11 - 14 V |
Wiring,
S17/4 |
| 4.0 |
 |
Trunk lock/trunk illuumination
rotary latch selector switch (S69/12)
Alarm circuit |
A37
59
(1.13) |
|
A37
4
(2)
|
Trunk lid:
closed
open |
< 1 V
11 - 14 V |
Wiring,
S69/12 |
| 5.0 |
|
Engine hood (S62)
Alarm circuit |
A37
5
|
|
A37
4
(2)
|
Engine hood:
closed
open |
< 1 V
11 - 14 V |
Wiring,
S62
|
| 6.0 |
|
Glove box switch
(ATA) (S62/7)
Alarm circuit |
A37
16 |
|
A37
4
(2)
|
Glove box:
closed
open |
< 1 V
11 - 14 V
|
Wiring,
S62/7 |
| 7.0 |
|
Stop lamp switch (S9/1) Alarm
circuit |
A37
3
(2) |
|
A37
12
|
Ignition: ON
Apply service brake: |
< 1 V
11 - 14 V
|
Wiring,
S9/1 |
| 8.0 |
|
Alarm horn (H3)
(only  )
As of 06/97: all vehicles until
06/98 |
A37
3
(4) |
|
A37
4
(2)
|
Insert bridge.
Use bridges with 124 589 37 63 00 safety cables only.
|
Alarm sounds.
|
Wiring,
H3 |
| 9.0 |
|
Alarm siren with auxiliary battery
(H3/1)
Function
(as of 06/98) |
|
|
|
HHT activation:
Alarm siren test. |
Siren emits short acoustic signal
for .2 sec seconds.
|
9.1 |
| 9.1 |
|
Voltage supply |
2 |
H3/1
|
1
|
Disconnect connector at
H3/1 |
11 - 14 V |
Wiring. |
| 9.2 |
|
Trigger alarm |
|
|
|
Activate ATA.
Wait 15 seconds.
Disconnect connector at
H3/1
To interrupt alarm, reconnect H3/1 connector and deactivate ATA.
|
Acoustical
and
Optical
alarm function. |
H3/1
Wiring,
A37 |
| 10.0 |
|
Not applicable for U.S.A. vehicles |
|
|
|
|
|
|
| 11.0 |
|
Headlamp
Alarm circuit |
A37
1
(2) |
|
A37
4
(4)
|
Insert bridge.
Use bridges with 124 589 37 63 00 safety cables only.
|
Headlamps are illuminated continuosly. |
Wiring,
Illumination control module (N7-1) |
| 12.0 |
|
Taillamp
Alarm circuit |
A37
1
(2)
4
(2) |
|
A37
4
(4)
4
(4)
|
Insert bridge.
Use bridges with 124 589 37 63 00 safety cables only. |
Left/right taillamps are illuminated
continuosly. |
Wiring,
Illumination control module (N7-1) |
| 13.0 |
|
ATA status/towing protection switch
(S85/3)
Deactivate anti-tow protection |
A37
6
(3) |
|
A37
3
(2)
|
Press top part of S85/3 switch. |
< 1  |
Wiring,
S85/3 |
| 14.0 |
|
ATA status indication via:
Interior switch (S6/1s1)
or
ATA status/towing protection switch (S85/3)
|
A37
11
(3) |
|
A37
4
(2)
|
Use bridges with 124 589 37 63 00 safety cables only. |
LED in switch illuminates. |
Wiring,
S85/3 or S6/1s2 |
| 15.0 |
     |
ATA tow sensor (B33)
Voltage supply
(only with anti-tow protection)
|
5 |
B33
|
2
|
Activate ATA. |
11 - 14 V
|
Wiring. |
| 15.1 |
|
Trigger alarm
(simulation) |
1 |
B33
 |
5
|
Disconnect connector at B33.
Insert bridge.
Use bridges with 124 589 37 63 00 safety cables only.
|
Alarm is triggered.
|
Wiring,
A37
If values are OK:
B33 |
Printable
version
