Diagnostic Manual, Chassis and Drivetrain,
Volume 3
| LOCATION: |
11.1 BAS > 23 Electrical Test Program - Test |
Electrical Test Program - Test
 |
 |
Test scope |
Test connection
|
Test condition |
Nominal value |
Possible cause/Remedy |
| 1.0 |
  
 |
BAS control module (N48)
Circuit 87
Voltage supply
|
1 
(1.1) |
N48
 |
 3 (1.3)
|
Ignition: ON |
11 - 14 V |
1.1,
1.2
|
| 1.1 |
|
Voltage supply from:
Models 129, 140
Base module (N16/1)
Models 202, 208, 210
Driver-side fuse and relay module box (K40/2)
|
|
|
N48
3 (1.3) |
Ignition: ON |
11 - 14 V |
Wiring,
Model 129, 140:
Fuse (F3) on N16/1,
N16/1,
DM, Chassis & Drivetrain, Vol. 1, sections 1.1,  23 |
| 1.2 |
|
Ground wire
Model 140
Model 170
Model 129
Models 202, 208
Model 210 |
W15
W35
W27
W29/2
W16/3
|
|
N48
1
(1.1) |
Ignition: OFF
Disconnect BAS control module (N48). |
< 1  |
Wiring,
Model 140: Ground (electronics ground output-right
footwell) (W15).
Model 129: Ground (control module box/module box) (W27).
Model 170: Ground (left front spring tower) (W35).
Models 202, 208: Ground (right A-pillar) (W29/2).
Model 210: Ground (output ground - left wheel housing ground) (W16/3).
|
| 2.0 |
|
BAS control module (N48)
Circuit 30
Voltage supply
|
1
(1.1) |
N48
|
4
(1.4)
|
Ignition: OFF |
11 - 14 V |
Wiring. |
| 3.0 |
|
Diagnosis output |
1
(1.1) |
N48
|
6
(1.6)
|
Ignition: ON |
1 - 2 V
|
Wiring,
BAS control module (N48). |
| 4.0 |
 |
Solenoid valve
(BAS) (A7/7y1)
Voltage supply |
1
(1.1) |
N48
|
12
(2.6)
|
Ignition: ON |
4.0 - 5.5 V |
4.1,
Wiring,
BAS control module (N48). |
| 4.1 |
|
Resistance |
9
(2.3) |
N48
 |
12
(2.6)
|
Ignition: OFF
Disconnect BAS control module (N48). |
1 - 2
|
Wiring,
Brake booster (BAS) (A7/7). |
| 5.0 |
 |
Membrane travel sensor (BAS) (A7/7b1)
Voltage supply |
1
(1.1) |
N48
|
13
(3.1) |
Ignition: ON
|
4.75 - 5.25 V |
Wiring,
BAS control module (N48). |
| 5.1 |
|
Ground |
14
(3.2)
|
N48
|
4
(1.4)
|
Ignition: ON |
11 - 14 V
|
|
 |
|
Printable version
