Test step
|
DTC |
Test scope
|
Test connection
|
Test condition
|
Nominal value
|
Possible cause/Remedy
|
| 1.0 |
 |
Cruise control switch (S40)
V Decelerate/set
B Accelerate/set
SP Resume
A Off
Control switch contact |
79  (1.38)
79 (1.38)
79 (1.38)
79 (1.38)
79 (1.38) |
|
 51 (1.10)
72 (1.31)
52 (1.11)
74 (1.33)
43 (1.2) |
Ignition: ON
Cruise control switch not activated
Position DECEL
Position RESUME
Position ACCEL
Switch not activated
Position OFF
Switch not activated
Control switch contact in position:
DECEL., ACCEL., RESUME OFF.
|
< 1 V
11 - 14 V
11 - 14 V
11 - 14 V
11 - 14 V
< 1 V
< 1 V
11 - 14 V |
Wiring,
Cruise control switch (S40). |
| 2.0 |
 |
Stop lamp switch (S9/1)
Signal (N.C. contact) |
79 (1.38)
|
N4/1
|
54 (1.13) |
Ignition: ON
Brake pedal not applied
Brake pedal applie
|
11 - 14 V
<1 V |
Wiring,
Stop lamp switch (S9/1),
Base module (N16/1),
DM, Chassis & Drivetrain, Vol. 1, section 1.1, |
| 3.0 |
|
Stop lamp switch (S9/1)
Signal (N.O. contact) |
79 (1.38) |
N4/1
|
71 (1.30) |
Ignition: ON
Brake pedal not applied
Brake pedal applied
|
<1 V
11 - 14 V |
Wiring,
Stop lamp switch (S9/1),
|
| 4.0 |
 |
Starter lock-out/backup lamp switch (S16/3)
Transmission range recognition voltage |
44
(1.3) |
N4/1
|
45
(1.4)
|
Ignition: ON
Transmission range
P 
R
N
D
3
2
|
1.0 V
0.3 V
4.0 V
3.5 V
2.5 V
1.8 V
(± 10%)
|
Wiring,
Starter lock-out/backup lamp
switch (S16/3),
 4.1 ,
EA/CC/ISC control module (N4/1). |
| 4.1 |
|
Starter lock-out/backup lamp switch (S16/3)
Resistance |
44 (1.3) |
N4/1
|
45
(1.4) |
Disconnect EA/CC/ISC control module (N4/1)
Ignition: ON
Transmission range
P
R
N
D
3
2
|
1.4 k 
294
28 k
11.3 k
5.9 k
3.1 k
(± 10%)
|
Wiring,
Starter lock-out/backup lamp
switch (S16/3). |
| 5.0 |
|
Non-USA vehicles only.
Continue to next test step.
|
|
|
|
|
|
|
| 6.0 |
 |
Left front axle vehicle speed
sensor (L6/1)
Speed signal |
79 (1.38) |
N4/1
|
56
(1.15) |
Lift front of vehicle:
Ignition: ON
Turn left front wheel by hand
|
4 - 8 V~ |
Wiring,
Left front axle vehicle speed
sensor (L6/1),
DM, Chassis & Drivetrain, Vol. 1, section 5.2,
Note:
Upon completion of test, erase DTC's stored in ABS/ASR control module memory.
|
| 7.0 |
 |
CAN data bus |
"L" |
N4/1x1
|
"H" |
Ignition: OFF
EA/CC/ISC control module (N4/1) disconnected.
Measure resistance at connector (see Figure 8)
|
55 - 65 |
Wiring,
LH-SFI control module (N3/1),
DM, Engines, Vol. 2, section 3.1,
Ignition control module (N1/2),
DM, Engines, Vol. 2, section 5.2. |
Printable version
